This instruction manual describes preventive maintenance and quick FANUC SYSTEM 3T-MODEL C is designated to be assembled inside an NC machine. Fanuc System 3T-Model D Operator’s Manual(BE 02) – Free download as PDF File .pdf) or read online for free. I am looking for an operators manual for a Fanuc 3 T controller used on a small Wasino gang lathe. Any help would be appreciated. Going to.

Author: Yozshudal Yozshurisar
Country: Kenya
Language: English (Spanish)
Genre: Technology
Published (Last): 1 February 2005
Pages: 129
PDF File Size: 7.49 Mb
ePub File Size: 2.33 Mb
ISBN: 193-5-74743-112-8
Downloads: 56751
Price: Free* [*Free Regsitration Required]
Uploader: Grogor

Zero return XZ axis.

Fanuc 3t Maintenance Manual

Posted via Mobile Device. The time now is Results 1 to 12 of Is there are process to set either the work offset or tool offset as relative to the absolute zero instead of the “random” zero?

fanc I have the original maintenance manual, but I could not find any parameters that seemed relevant. In my 21 those parameters start at First If you can post more pic’s, How Deep did you go into the mechinacal of the Lathe Bearing’s and such I have machine of the same model I have maintnace manual’s and programing with paramiter list’s If I can Help at pressent mine is down with a spindel drive issue I have Igbat’s to replace and have so far replaced one the local frelance Fanuc tec told me that the top one was the most likley to be the one dead but no change in symptom’s after changing it will move on and test as I change to hopefuly find the proublem.

Ad text and spelling.

Somewere I have littutaure on gang tooling from a local dealer for now I mounted a Quick change tool post on the slide with a riser plate ok for short run’s with few tool’s Keep up th good work You can contact me ktaylor earthlink.


I’m very familiar with machining centers, but I’m in need of some assistance translating that into “ancient” CNC lathe operation. Originally Posted by fordav So if the table moves 1″, the readout said 2″. Now does anybody know what is needed to upgrade to 80m?

Thanks fomaz, I already have the original yellow floppy maintenance manual which theoretically describes all of the “non-option” parameters.

I’m using basic G-code group A and the very basic M codes to try to program this thing. Program input is not started with the data input external start signal MINP.

Fanuc 3T Parameters Manual pdf – CNC Manual

Imagination will take you everywhere. I have tool offsets which are settable from the MDI. By roymanvega in forum Fanuc. The ballscrews were actually fresh and the table had no appreciable backlash less than a tenth of a thou. Helwig Carbon are a source of brushes, BTW. Results 1 to 10 of Started out like this: Anybody know if thats an canuc you can add afterwards?

I need some help setting tool offsets when I get up and running again Thank’s Kevin. IndustryArena uses cookies to ensure you get the best experience on our website. I would like to find a manual that goes into the disambly of the head stock 3h slides. Parameter 8 relates to axis parameters for reference counter and multiplying ratio.

When you program the job make sure you have G28 U0 W0 at the end of each tool.

So here’s some before pictures. While you do not have a parameter manual you can see if you have those parameters. I’ve cut a couple things on it since the G50 discovery, the first cut was this buffer. We should also compare parameters and diagnostics. Mostly I took everything that I could unbolt apart and sandblasted it, did have to fix the turcite on one of the ways.


Fanuc 3T Parameters Manual

One last question, am I crazy for thinking of adding a C-axis to this machine? Fanuc paramater’s Yaddatrance are you in the US Location? Zero return the machine, then on the position page X[origin] Z[origin] to zero the position readout.

I worked a 3T many years ago. It has a kitagawa actuator and I just barely see a company logo that begins with M on the spindle housing. I need the parameter list to get the machine working.

From my admittedly limited understanding, I have the absolute zero which I can tweak with gridshift offsets, but does not seem to be used for anything except G28, e.

I’m wishing Fanuc had more info on these older units. Now I just need to figure out if there’s any way to set DNC on this machine Tags for this Threadmachining centerssinceuseful. You will need it vanuc times. When I power the machine on, it sets zero as where-ever the table currently sits.

In any event, it seems to be new enough to support tool offsets. Also, where the heck do you buy gang-tool style bits? By the way good work on the retrofit.

So my question probably should be. From his recollection, fanu 3T normally has 20m 8KB of memory and is expandable to 40m onboard, up to 80m with additional memory cards. The parameter descriptions are in the back of a Fanuc System 3T operator manual. What did they use originally?