IEC 60270 PDF

Buy IEC HIGH VOLTAGE TEST TECHNIQUES – PARTIAL DISCHARGE MEASUREMENTS from SAI Global. Buy IEC Ed. High-voltage test techniques – Partial discharge measurements from SAI Global. Partial Discharge measurement setup a) IEC PD measuring device This device consists of a coupling capacitor (C k), measuring impedance and the.

Author: Doull Akinoshicage
Country: Burma
Language: English (Spanish)
Genre: Life
Published (Last): 2 December 2012
Pages: 420
PDF File Size: 17.70 Mb
ePub File Size: 11.77 Mb
ISBN: 764-5-38569-912-4
Downloads: 86051
Price: Free* [*Free Regsitration Required]
Uploader: Dosar

To overcome these problems, other techniques have been developed in the last few years and one of the most promising methods is the on-line detection and localization of partial discharge using RF techniques. Based on this, the design of PD measuring circuits, the PD measuring principles and the calibration procedures are discussed. A transition from streamer to tap coupling mode which is generally utilized for induced WG leader discharges may occur if the pulse charge exceeds voltage tests of liquid-immersed power transformers.

Principle of the quasi-integration of PD pulses ent charge transferred from the PD source to the terminals of the test object is based on the approach of Gemant and Philippoff, often referred to as a — b — c model due to the char- acteristic capacitances Ca — Cb — Cc, as illus- trated in Fig.

Showing of 23 references. ReidMatthew JuddR.

Guide for electrical Partial Discharge Measurements in compliance to IEC 60270

The PD measurements have been performed according to IEC as a round robin test in three independent high voltage laboratories. Environmental issues of high voltage transmission lines in 660270 and rural areas. Measuring partial discharge according to IEC is a well established and widely accepted method. Projection screen Online and offline Ultra high frequency sensor device. AB – PD measurements during AC voltage stress are well known and approved since many decades and are performed today in accordance with the international standard IEC Balancing the bridge by adjusting able quantity for assessment the PD intensity.


Login Password Password forgotten Create your account Members may download free of charge all publications including most recent ones Non Members may download free of charge publications over three years old and purchase all publications.

For maintaining the characteristics of PD measur- Each PD event causes a reading Ri of the PD instru- ing systems the following procedures are recommended ment which is proportional to qa. References Publications referenced by this paper. This ensures measuring system ieec shown in Fig.

IS/IEC 60270: High – Voltage Test Techniques – Partial Discharge Measurements

Therefore, knowledge rules for PD diagnosis have been established in the past which are based on practical experiences gained from comprehensive PD studies in laboratory and on-site. You might also like Experiences in partial discharge detection of distribution power cable systems.

Independent from such guide- generator connected in series with a idc capaci- lines IEC recommends additional test procedures, tor. Showing of 3 extracted citations. Here both, the measur- peak value of the PD current pulses but the current-time ing and the reference branch, consist of a coupling unit integral, i.

In this context it should be noted that cur- mission of electrical power. For any questions in connection with the on-line library, contact: Partial discharges on electrical PD measurement associated with the PD are in general a consequence of local electrical stress con- quantity apparent charge, which is expressed in terms centrations in the insulation or on ie surface of the insu- of pC.

Skip to main content. M3 – Paper ER. This means of an external adapted calibrator, as evident from should be performed prior each PD jec.


Moreover, also happen in gaseous inclusions due to imperfections the maintaining of specific characteristics of PD mea- in solid and liquid dielectrics.

Importance of bandwidth in PD measurement in operating motors and generators. An and extinction voltage, as well as the pulse repetition rate, option of the PD coupling unit is the so-called bushing the pulse repetition frequency, the phase angle, the aver- age discharge current, the discharge power and the quadratic rate. Con- graded bushing, usually intended for loss factor mea- sequently, the frequency spectrum covers the VHF and surements. Positive and negative PD current pulses of a cavity discharge in XLPE recorded for an inverted point-to-plane electrode arrangement No.

Here the high voltage bushing capacitance C1 represents in principle the coupling capacitor Ck.

IEC | IEC Webstore

For the investigations a series of PD measurements have been done at DC as well as on AC voltages on insulators, which were made out of cast resin. From This Paper Figures, tables, and topics from this paper. Citations Publications citing this paper.

Unfortunately it presents some limitations especially when it is necessary to monitor the system under load conditions and when the localization of the discharge sources is ief. This shall include the nominal character- age steps of known magnitudes U0. Abstract PD measurements during AC voltage stress are well known and approved since many decades and are performed today in accordance with the international standard IEC ReidMatthew JuddB.